ECS1008P/ECS1112FP

v1.2.90

  • Support HTTPs-only function (from device side).

  • Fixed the issue that switch may not sync all configurations with Cloud at the first check-in.

  • Add enhancement to prevent switch out of memory.

v1.2.88

  • Fixed the issue where IPv6 address in network settings cannot be saved after reboot.

  • Fixed CPU loading issue upon parsing DHCP traffics for wired client information.

  • Fixed the error display for CPU loading on EnGenius cloud dashboard.

v1.2.85 (Obsolete, replaced by v1.2.88)

  • Add CLI command for wired client-list function: wired client list { enable | disable }

  • Modify DHCP packet's host name (Option 12) to include model name and add 4 MAC address digits (2-bytes).

  • Change default configurations:

    1. DHCP snooping is disabled by default.

    2. Wired client list is enabled by default.

  • Add CLI command to support config VLAN range.

  • Implement CLI commands that can show current config of specified feature.

  • Add CLI commands to support displaying 5-min port utilization records for past 24 hours.

  • Add CLI command to support showing different running config.

  • Modify the LLDP-MED TLV value content when connecting to Senao Extender.

  • Support manually disable / enable cloud agent by CLI and Local GUI.

  • Change default config to disable IPv6 default route.

  • Enhance Cloud agent to support 802.1x+MAB feature.

  • Support the wired client list feature.

  • Disable both flow control and 802.1x on ECS switch's default configurations.

  • Adjust the system-name parameter to read-only on LSP page.

v1.2.76

  • Integrate ACLG (Auto-CAM life-guard) into the PDLG.

  • Add ONVIF discovery feature.

  • Support VTP (VLAN trunking port) for 1 ~ 4094 VLAN ID.

  • Enclose system name for displaying in syslog messages.

  • Support system name using UTF-8.

  • Support port isolation and grouping (Please be advised the isolation settings will need re-configuration due to feature update where forward ports can be specified for a chosen port when port isolation is enabled).

v1.2.73

  • Support MDNS and SSDP discovery protocols.

  • Support LBD function per port setting.

  • Add Private-VLAN function. (via CLI and local GUI for now)

  • Support LSP function.

  • Fine-tune the abnormal last update time issue for cloud_agent.

  • Support Gratuitous ARP function.

  • Support single port binding to trunking member via local GUI.

  • Enhance ECS1008P (v2) to support AT mode.

v1.2.72

  • Enhance Cloud Agent to support MAF. (MAC address filtering)

  • Known Issue: in [MLD Snooping][Router Settings], when adding a port into static port list, the port will show as "T", instead of "S".

  • Known Issue: in [Web][Port Settings], Fiber ports will stop working after setting 1Gbps/Full from web then changing to other speed; this can be recovered by disabling/enabling the port.

v1.2.71

  • Fix abnormal gateway configuration in the DHCP relay environment.

  • Fixed the issue of VLAN name synchronization when the VLAN name contains special characters such as parentheses (e.g., '()').

  • Add BPDU Guard / Root Guard for STP protocol feature.

  • Add SNMPv3 configurations for cloud agent.

  • Add MVR feature.

  • Enclose fix for CVE-related issue (no_dirlist).

v1.2.70

  • Support multiple Regions (including Japan).

  • Revise system name to be “Model Name” followed by “-“ with last 4 digits of device MAC address (for example, ECS5512-38f8).

v1.2.69

  • Support web proxy server feature in local GUI for cloud agent.

  • Enhance switch sync mechanism with cloud and cloud check-in time.

  • Enclose fix to prevent switch hang upon configuring static IPv4 address to switch device.

  • Modify the action when schedule.db changes for scheduled PoE feature.

  • Modify the log handling with Cloud about flick reboot.

  • Fix switch hang issue with IGMP and MLD for IPTV integration.

  • Fix potential segmentation fault issue for the routing feature.

v1.2.68

  • Packet capture supports both Tx/Rx feature.

  • Fix the issue when an user configured VLAN name with a space character via the cloud, it will not sync to the device.

v1.2.65

  • Add MAC-Authentication-Bypass feature.

v1.2.64

  • Add ONVIF camera discovery feature.

  • Modified the trunk binding rule to bypass the media type check mechanism, allowing binding with different link speeds.

v1.2.63

  • Update the number of VLAN entries to 1024.

v1.2.62

  • Fix the firmware upgrade issue when the switch current firmware version is from very early version.

v1.2.61

  • Support Packet Capture in Diag Tools on EnGenius Cloud for cloud-managed ECS switch.

v1.2.60

  • Support Diag Tools on EnGenius Cloud for cloud-managed ECS switch.

v1.2.59

  • Apply new GUI design to device's web management pages.

  • Add DHCP IP auto-renew mechanism when cloud agent cannot check-in to server.

v1.1.58

  • Support optimized IGMP fast leave.

v1.1.57

  • Fine-tune ARP-validation mechanism to accommodate Mesh feature with ECW Cloud AP.

v1.1.55

  • Enhance PD Lifeguard feature with pending expiration.

  • Add "Version ID" for IGMP feature.

v1.1.52 (obsolete and will be updated soon)

  • Change Syslog write to flash level from INFO to Critical.

  • Support VLAN 0 to facilitate forwarding behavior.

  • Disable SSDP and mDNS features temporarily to avoid memory sizing issues.

  • For Multi-G series switches, PHY settings are adjusted to keep better ability of Interconnection to support most link-partners.

v1.1.49

  • Adjust header parsing rule for time-zone parameter. (cloud agent)

  • Adjust the SSDP and mDNS default configuration to disable. (It won't handle SSDP and mDNS packets by default setting.)

v1.1.47

  • Switch PoE scheduling feature will let user configure schedule via Cloud GUI when the device is powered by PoE of the port.

  • Switch LED on/off feature allows switch LED to be turned off at the upper-right corner in switch device detail page via Cloud GUI. (please be advised PoE Mode/LAN Mode LED cannot be turned off due to hardware limitation.)

  • Reset PoE from the port panel allows user to mouse-over PoE ports on switch port panel via Cloud GUI and power-cycle the port so the device attached to the port can be rebooted.

v1.1.42

  • Add GET/SET SNMP community for cloud agent.

  • Fix abnormal static route entry issue.

  • Fix abnormal default gateway issue.

  • Fix abnormal uplink port issue.

v1.1.40

  • Add Connection Diagnostic page in ECS local web management.

  • Add “Extend” link-speed mode in port setting page. (Not supported in multi-G series because it is without 10Mbps-speed.)

  • Support 2K static VLAN entries.

  • Adjust the hybrid service priority for Cloud Agent and WTP process.

  • Add "On", "Off" action for Scheduled PoE.

  • Add DHCP snooping / relay features for Cloud Agent.

v1.1.36

  • Update LED behavior code to cope with multi-G (5Gbps/2.5Gbps) LED color change from green to amber. 10Gbps LED remains green and 100Mbps/1Gbps remain amber as in previous v1.1.35.

v1.1.35

Bug Fixes

  • Fix DHCP client function that may cause system crash issue.

v1.1.31

Improvements

  • Resolve LBD behavior issue when STP enabled.

  • Add LLDP remote information ''system description'', ''remote capability support'', and ''remote capability enable''.

  • Renew the DNS server IP when receiving DHCP offer packet.

Bug Fixes

  • Resolve memory leak caused by abnormal DHCP packets.

v1.1.29

Improvements

  • Accommodate loop back detection mechanism for IOT devices.

  • Support trunk and mirror settings for cloud management.

  • Improve the efficiency to initiate cloud management service.

  • Add system warm start log to denote an expected software reboot.

  • Adjust default value of port rate limit to 1Mbps.

  • Web GUI now follows new 2020 California Password Law (SB-327) to force user changing password for a first time login.

  • Improve the way to show STP block/unblock status.

  • Support configure local credential in Cloud. Note that if the cloud already configured a different credential, the local credential will be synced to the cloud one automatically.

Bug Fixes

  • Fix the issue of packet buffer leak which may cause a system reboot.

  • Fix the issue that some specific DHCP packets sent by mikrotik router may cause system reboot.

  • Fix the bug that recurring setting of daylight saving does not work when SNTP service is not available.

v1.1.21

Improvements

  • Support cloud configuration on per port PVID and vlan members.

Bug Fixes

  • Correct the syslog timestamp issue.

  • Fix GUI and CLI issue by limiting the input format of User Account to Letters, Numbers, and underline character '_' only.

  • Fix GUI and CLI issue by excluding character '@' from password string.

v1.1.19

Improvements

  • Enhance DHCP settings to accommodate 2 sets of DNS server IP upon receiving multiple sets of DNS server IP from DHCP server.

  • Add system restart logs.

Bug Fixes

N/A

Last updated