ESG610

v1.2.48

Fixed the issue for Auto Site-to-Site VPN connection sometimes getting disconnected upon WAN function reloaded with the following conditions:
- Case 1: WAN IP is being changed (e.g., PPPoE IP changed)
- Case 2: Fail-over under dual WAN
- Case 3: IP getting changed in front end of Gateway
Fixed the issue for Diag Tool sometimes showing "This device is unavailable".

Fixed the issue for Site to Site VPN and IPsec Client VPN function that do not work properly with BASIC license.

Support Policy Route.
Support Gateway Access Control: VIP List and Block List.
Support Firewall Traffic Log - syslog server.
Support Packet Capture for WAN interfaces.
Adjust the definition and behavior of "System Name" and "Device Name"
- Remove System Name setting from LSP.
- Revise DHCP client hostname to {ModelName}-{MAC_last_4_digits}.
- System Name support multi-language.
Automatically add a GRE port forwarding rule while adding PPTP TCP port: 1723
Revise Subnet Mask format of Static IP in LSP.
Optimize reset button behavior.
Fixed Gateway status issue when it shows online, it doesn't show WAN1/WAN2 IP information in Cloud UI.
Fixed the issue for Auto VPN where it failed if the number of ESG devices is more than 11.
Fixed the issue where the system becomes stuck upon continuously adding two bridge interfaces without assigning any Ethernet ports.

Use System Name as Host name for WAN via DHCP.
Enhance WAN security to close port 53 if Outbound FQDN rules are set.
Fixed the issue for Site-to-Site VPN connection not established after system reloading in some cases.
Fixed the issue for SecuPoint server to let it work in Passthrough Mode or under NAT.
Support URL filtering and Block page. (Cloud page to be updated)
Support EnGenius and 3rd-party DDNS function in Passthrough Mode. (Cloud page to be updated)
Support Client traffic statistics. (Cloud page to be updated)

Support Site-to-Site VPN Failover for ESG and Non-EnGenius Gateway.
Support EnGenius DDNS.
Support EnGenius SecuPoint VPN.
Fixed the routing issue upon enabling dual WAN where WAN interfaces have the same WAN gateway.
Note for Enhanced Security: The new firmware version (1.2.37) will remove the support for the less secure 3DES and MD5 options in IPSec Site-to-Site VPN Phase 2 settings, enhancing your data protection.

Add WWAN Failover Preference setting.
Add WWAN information for network statistics, packet loss, latency, and throughput.
Add USB port status for cellular dongle information.
Support PoE Reset function.
Support WAN1, WAN2, and WWAN Speed Test in Diag Tool.
Revise System Name synchronization mechanism: (1) ESG610 will always set "System Name" according to cloud configuration. (2) ESG610 will synchronize "System Name" ONLY ONCE from DUT to Cloud if user manually revises it through LSP.
Revise LSP GUI style.
Fixed the Failover function fail issue when WAN1 or WAN2 has been assigned an IP address but is unable to access the Internet.
Fixed the Failover function when it sometimes fails to resume the primary WAN connection.
Fixed the issue that ESG610 is unable to reconnect to Non-EnGenius peer after Site-to-Site VPN connection is disconnected.
Fixed the issue for incorrect type setting of Local / Remote ID in Non-EnGenius Site-to-Site VPN settings.
Fixed the issue for incorrect DHCP Client ID on the WAN interface where the content of Option 61 should be the MAC address of ESG610 rather than "ESG610".
Fixed the issue for Event Log where it continuously displays firmware upgrade and applied configuration messages while the device is being upgraded.
Fixed the issue for captive portal page not able to redirect to external splash page.

Add a function to override WAN MAC address setting on LSP.
Add a function to support Multi-Bridge function.
Add a function to support Per-Client bandwidth limitation.
Adjust the algorithm of Dual WAN failover function.
Revise Diag Tools for CPU loading stability.
Fixed the connection status issue where Non-EnGenius Peers' connection is connected but status is incorrect.
Fixed incorrect throughput result of WAN speed in Diag Tools.

Remove VPN disconnect message if it is caused by Re-Authentication.
Client VPN function failed in Passthrough mode.
Fail to set up DNS servers in WAN2 when WAN2's DNS server is set up to "Using Google Public DNS" or set up to "8.8.8.8/8.8.4.4" manually.
SIP compatibility issue.
Auto VPN function sometimes doesn't work.

Last updated 17 days ago