ESG620

V1.2.70

[New Features]

• Support Static Route over VPN: Enables traffic control by manually defining routes over a VPN tunnel, optimizing network efficiency.

• Support Default Route to Remote Hub: allows routing all traffic through the remote hub for enhanced security and centralized traffic management

• Support to save device’s log to syslog server for centralized log management

• Support real-time log download to easy troubleshooting

• Changes ESG510/ESG610/ESG620 Ethernet LED definition to “Green is high speed; amber is lower speed”

• Add warning message for WAN/LAN IP conflicts to alert users of potential network issues

• Enhanced L7 firewall detection to improve accuracy in identifying Layer 7 packets

[Issues Fixed]

• Fixed issue where only one L2TP connection from a LAN site could be established to an L2TP VPN server at the WAN site

• Fixed issue where clients failed to obtain an IP address when switching WAN2 and LAN via the Local Status Page (LSP) while the internet was unreachable.

V1.2.67

[Issues Fixed]

• Fix the WAN disconnect issue when connecting to Verizon network.

V1.2.66

[Issues Fixed]

• Fixed the issue where Captive Portal's click-through authentication failed when many users were logging in

• Fixing the NTP Mode 6 Scanner enhances system security and reduces potential attack risks.

• Fixed the issue where ICMP Timestamp Request Disclosure exposed system time

v1.2.65

[New Features]

• Support Layer 7 Policy Based Route, allows administrator to designate which WAN port to be used for different applications.

• Support Layer 7 firewall rule to block specific application that may hurt you network.

• Support rollback configuration to prevent configuration errror that impact cloud connections.

• Increase Layer 3 and Layer 7 firewall event logs, improving traffic visibility and easier for administrator troubleshoot their network.

• Direct SecuPoint VPN user traffic using the gateway's PBR settings to ensure that all user traffic follows the same rules

• Enhanced WAN disconnected log making WAN troubleshoot easier.

• Support to disable LLDP for specific environment that do not allow auto discovery protocols. (Cloud does not support yet)

• Support mDNS function making ESG easier to be found in local network. (Cloud does not support yet)

[Issues Fixed]

• Fixed the issue where LAN subnets matching PBR rules could not route to other local subnets.

• Fixed the issue that SecuPoint remote client can't access ESG’s local LAN if Passthrough mode and Split tunnel are enabled.

v1.2.60

[New Features]

• Enhanced firewall logs to output as a text file in real-time. (Cloud does not support yet)

• Auto VPN Hub-and-Spoke supports full tunnel mode. (Cloud does not support yet)

• Added support for static routing over VPN. (Cloud does not support yet)

• When a rogue DHCP server is detected, an event log notification will be generated.

• Added support to export NAT logs to an external syslog server. (Cloud does not support yet)

• New dashboard displays WWAN information when WWAN is the primary WAN.

• Added a new event log for reaching the maximum number of SecuPoint client seats.

• Added a new event log for when the public IP and WAN IP are configured the same in NAT.

• Support enable/disable HTTPs-only for local web page access. Allowing users force web UI access encrypted for better security.

• Support enable/disable Local Web Page. Allowing users forbid local managements to prevent the confliction with the central cloud management.

[Issues Fixed]

• Resolved an issue where the DDNS hostname was not displayed in the SecuPoint VPN client when passthrough mode was enabled.

• Fixed an issue where the SecuPoint VPN client was non-functional when the primary WAN2 connection type was set to DHCP or a static IP address.

• Addressed an issue where an Android phone (SecuPoint VPN client) could not access the internal server when SecuPoint VPN and port forwarding were enabled.

• Corrected an issue where the latency monitor was inaccurate when the PBR function was enabled.

• Fixed a problem with the Diag tool to prevent response failures.

• Resolved an issue where the S2S VPN connection failed when the ESG uplink gateway changed its WAN IP address.

• Fixed an issue where the VPN connection failed when the primary WAN was WAN2.

v1.2.48

• Fixed the issue for Auto Site-to-Site VPN connection sometimes getting disconnected upon WAN function reloaded with the following conditions:

  • Case 1: WAN IP is being changed (e.g., PPPoE IP changed)

  • Case 2: Fail-over under dual WAN

  • Case 3: IP getting changed in front end of Gateway

• Fixed the issue for Diag Tool sometimes showing "This device is unavailable".

v1.2.47

• Fixed the issue for Site to Site VPN and IPsec Client VPN function that do not work properly with BASIC license.

v1.2.46

• Support Policy Route.

• Support Gateway Access Control: VIP List and Block List.

• Support Firewall Traffic Log - syslog server.

• Support Packet Capture for WAN interfaces.

• Adjust the definition and behavior of "System Name" and "Device Name"

  • Remove System Name setting from LSP.

  • Revise DHCP client hostname to {ModelName}-{MAC_last_4_digits}.

  • System Name support multi-language.

• Automatically add a GRE port forwarding rule while adding PPTP TCP port: 1723

• Revise Subnet Mask format of Static IP in LSP.

• Optimize reset button behavior.

• Fixed Gateway status issue when it shows online, it doesn't show WAN1/WAN2 IP information in Cloud UI.

• Fixed the issue for Auto VPN where it failed if the number of ESG devices is more than 11.

• Fixed the issue where the system becomes stuck upon continuously adding two bridge interfaces without assigning any Ethernet ports.

v1.2.40

• Use System Name as Host name for WAN via DHCP.

• Enhance WAN security to close port 53 if Outbound FQDN rules are set.

• Fixed the issue for Site-to-Site VPN connection not established after system reloading in some cases.

• Fixed the issue for SecuPoint server to let it work in Passthrough Mode or under NAT.

• Fixed the issue for ESG620 not able to connect to EnGenius Cloud via WAN2 connection when an unsupported SFP+ module is plugged into WAN1 port.

• Support URL filtering and Block page. (Cloud page to be updated)

• Support EnGenius and 3rd-party DDNS function in Passthrough Mode. (Cloud page to be updated)

• Support Client traffic statistics. (Cloud page to be updated)

v1.2.37

• This f/w version is for the first release.