Comment on page
ECS15XX/ECS25XX
ECS Switches with 10G uplink ports including: ECS1528/ECS1528FP/ECS1552/ECS1552FP/ECS2512FP/ECS2512
- Integrate ACLG (Auto-CAM life-guard) into the PDLG.
- Add ONVIF discovery feature.
- Change the jumbo frame size to 12KB.
- Support VTP (VLAN trunking port) for 1 ~ 4094 VLAN ID.
- Enclose system name for displaying in syslog messages.
- Support system name using UTF-8.
- Support port isolation and grouping (Please be advised the isolation settings will need re-configuration due to feature update where forward ports can be specified for a chosen port when port isolation is enabled).
- Support MDNS and SSDP discovery protocols.
- Support LBD function per port setting.
- Add Private-VLAN function. (via CLI and local GUI for now)
- Support LSP function.
- Fine-tune the ping delay time issue.
- Fine-tune the abnormal last update time issue for cloud_agent.
- Support Gratuitous ARP function.
- Support single port binding to trunking member via local GUI.
- Enhance Cloud Agent to support MAF. (MAC address filtering)
- Known Issue: in [MLD Snooping][Router Settings], when adding a port into static port list, the port will show as "T", instead of "S".
- Known Issue: in [Web][Port Settings], Fiber ports will stop working after setting 1Gbps/Full from web then changing to other speed; this can be recovered by disabling/enabling the port.
- Fix abnormal gateway configuration in the DHCP relay environment.
- Fix abnormal LLDP TLV format for SFP port. (e.g., ECS2512FP)
- Fixed the issue of VLAN name synchronization when the VLAN name contains special characters such as parentheses (e.g., '()').
- Add BPDU Guard / Root Guard for STP protocol feature.
- Add SNMPv3 configurations for cloud agent.
- Add MVR feature.
- Enclose fix for CVE-related issue (no_dirlist).
- Support multiple Regions (including Japan).
- Revise system name to be “Model Name” followed by “-“ with last 4 digits of device MAC address (for example, ECS5512-38f8).
- Support web proxy server feature in local GUI for cloud agent.
- Enhance switch sync mechanism with cloud and cloud check-in time.
- Enclose fix to prevent switch hang upon configuring static IPv4 address to switch device.
- Modify the action when schedule.db changes for scheduled PoE feature.
- Modify the log handling with Cloud about flick reboot.
- Fix switch hang issue with IGMP and MLD for IPTV integration.
- Fix potential segmentation fault issue for the routing feature.
- Packet capture supports both Tx/Rx feature.
- Fix the issue when an user configured VLAN name with a space character via the cloud, it will not sync to the device.
- Add MAC-Authentication-Bypass feature.
- Add ONVIF camera discovery feature.
- Modified the trunk binding rule to bypass the media type check mechanism, allowing binding with different link speeds.
- Update the number of VLAN entries to 2048.
- Fix the firmware upgrade issue when the switch current firmware version is from very early version.
- Support Packet Capture in Diag Tools on EnGenius Cloud for cloud-managed ECS switch.
- Support Diag Tools on EnGenius Cloud for cloud-managed ECS switch.
- Apply new GUI design to device's web management pages.
- Add DHCP IP auto-renew mechanism when cloud agent cannot check-in to server.
- Support optimized IGMP fast leave.
- Fine-tune ARP-validation mechanism to accommodate Mesh feature with ECW Cloud AP.
- Enhance PD Lifeguard feature with pending expiration.
- Add "Version ID" for IGMP feature.
- Add supported model for ECS1552FPv2 and ECS1528FPv2
- Change Syslog write to flash level from INFO to Critical.
- Support VLAN 0 to facilitate forwarding behavior.
- Disable SSDP and mDNS features temporarily to avoid memory sizing issues.
- For Multi-G series switches, PHY settings are adjusted to keep better ability of Interconnection to support most link-partners.
- Adjust header parsing rule for time-zone parameter. (cloud agent)
- Adjust the SSDP and mDNS default configuration to disable. (It won't handle SSDP and mDNS packets by default setting.)
- Switch PoE scheduling feature will let user configure schedule via Cloud GUI when the device is powered by PoE of the port.
- Switch LED on/off feature allows switch LED to be turned off at the upper-right corner in switch device detail page via Cloud GUI. (please be advised PoE Mode/LAN Mode LED cannot be turned off due to hardware limitation.)
- Reset PoE from the port panel allows user to mouse-over PoE ports on switch port panel via Cloud GUI and power-cycle the port so the device attached to the port can be rebooted.
- Add GET/SET SNMP community for cloud agent.
- Fix abnormal static route entry issue.
- Fix abnormal default gateway issue.
- Fix abnormal uplink port issue.
- Fix EEE feature not able to save power issue. (for all ECS Multi-G series)
- Add Connection Diagnostic page in ECS local web management.
- Add “Extend” link-speed mode in port setting page. (Not supported in multi-G series because it is without 10Mbps-speed.)
- Support 2K static VLAN entries.
- Adjust the hybrid service priority for Cloud Agent and WTP process.
- Add "On", "Off" action for Scheduled PoE.
- Add DHCP snooping / relay features for Cloud Agent.
- Update LED behavior code to cope with multi-G (5Gbps/2.5Gbps) LED color change from green to amber. 10Gbps LED remains green and 100Mbps/1Gbps remain amber as in previous v1.1.35.
- Fix DHCP client function that may cause system crash issue.
- Resolve LBD behavior issue when STP enabled.
- Add LLDP remote information ''system description'', ''remote capability support'', and ''remote capability enable''.
- Renew the DNS server IP when receiving DHCP offer packet.
- Resolve memory leak caused by abnormal DHCP packets.
- Accommodate loop back detection mechanism for IOT devices.
- Support
trunk
andmirror
settings for cloud management. - Improve the efficiency to initiate cloud management service.
- Add system
warm start log
to denote an expected software reboot. - Adjust default value of port rate limit to 1Mbps.
- Web GUI now follows new 2020 California Password Law (SB-327) to force user changing password for a first time login.
- Improve the way to show
STP block/unblock status
. - Support configure local credential in Cloud. Note that if the cloud already configured a different credential, the local credential will be synced to the cloud one automatically.
- Fix the issue of packet buffer leak which may cause a system reboot.
- Fix the issue that some specific DHCP packets sent by Mikrotik or Huawei router may cause system reboot.
- Fix the bug that recurring setting of daylight saving does not work when SNTP service is not available.
- Support cloud configuration on per port PVID and vlan members.
- Correct the syslog timestamp issue.
- Fix GUI and CLI issue by limiting the input format of User Account to Letters, Numbers, and underline character '_' only.
- Fix GUI and CLI issue by excluding character '@' from password string.
- Enhance DHCP settings to accommodate 2 sets of DNS server IP upon receiving multiple sets of DNS server IP from DHCP server.
- Add system restart logs.
N/A
Last modified 2d ago