ECS1008P/ECS1112FP/ECS1128FP/ECS1152FP
v1.2.88
Fixed the issue where IPv6 address in network settings cannot be saved after reboot.
Fixed CPU loading issue upon parsing DHCP traffics for wired client information.
Fixed the error display for CPU loading on EnGenius cloud dashboard.
v1.2.85 (Obsolete, replaced by v1.2.88)
Add CLI command for wired client-list function: wired client list { enable | disable }
Modify DHCP packet's host name (Option 12) to include model name and add 4 MAC address digits (2-bytes).
Change default configurations:
DHCP snooping is disabled by default.
Wired client list is enabled by default.
Add CLI command to support config VLAN range.
Implement CLI commands that can show current config of specified feature.
Add CLI commands to support displaying 5-min port utilization records for past 24 hours.
Add CLI command to support showing different running config.
Modify the LLDP-MED TLV value content when connecting to Senao Extender.
Support manually disable / enable cloud agent by CLI and Local GUI.
Change default config to disable IPv6 default route.
Enhance Cloud agent to support 802.1x+MAB feature.
Support the wired client list feature.
Disable both flow control and 802.1x on ECS switch's default configurations.
Adjust the system-name parameter to read-only on LSP page.
v1.2.76
Integrate ACLG (Auto-CAM life-guard) into the PDLG.
Add ONVIF discovery feature.
Support VTP (VLAN trunking port) for 1 ~ 4094 VLAN ID.
Enclose system name for displaying in syslog messages.
Support system name using UTF-8.
Support port isolation and grouping (Please be advised the isolation settings will need re-configuration due to feature update where forward ports can be specified for a chosen port when port isolation is enabled).
v1.2.73
Support MDNS and SSDP discovery protocols.
Support LBD function per port setting.
Add Private-VLAN function. (via CLI and local GUI for now)
Support LSP function.
Fine-tune the abnormal last update time issue for cloud_agent.
Support Gratuitous ARP function.
Support single port binding to trunking member via local GUI.
Enhance ECS1008P (v2) to support AT mode.
v1.2.72
Enhance Cloud Agent to support MAF. (MAC address filtering)
Known Issue: in [MLD Snooping][Router Settings], when adding a port into static port list, the port will show as "T", instead of "S".
Known Issue: in [Web][Port Settings], Fiber ports will stop working after setting 1Gbps/Full from web then changing to other speed; this can be recovered by disabling/enabling the port.
v1.2.71
Fix abnormal gateway configuration in the DHCP relay environment.
Fixed the issue of VLAN name synchronization when the VLAN name contains special characters such as parentheses (e.g., '()').
Add BPDU Guard / Root Guard for STP protocol feature.
Add SNMPv3 configurations for cloud agent.
Add MVR feature.
Enclose fix for CVE-related issue (no_dirlist).
v1.2.70
Support multiple Regions (including Japan).
Revise system name to be “Model Name” followed by “-“ with last 4 digits of device MAC address (for example, ECS5512-38f8).
v1.2.69
Support web proxy server feature in local GUI for cloud agent.
Enhance switch sync mechanism with cloud and cloud check-in time.
Enclose fix to prevent switch hang upon configuring static IPv4 address to switch device.
Modify the action when schedule.db changes for scheduled PoE feature.
Modify the log handling with Cloud about flick reboot.
Fix switch hang issue with IGMP and MLD for IPTV integration.
Fix potential segmentation fault issue for the routing feature.
v1.2.68
Packet capture supports both Tx/Rx feature.
Fix the issue when an user configured VLAN name with a space character via the cloud, it will not sync to the device.
v1.2.65
Add MAC-Authentication-Bypass feature.
v1.2.64
Add ONVIF camera discovery feature.
Modified the trunk binding rule to bypass the media type check mechanism, allowing binding with different link speeds.
v1.2.63
Update the number of VLAN entries to 1024.
v1.2.62
Fix the firmware upgrade issue when the switch current firmware version is from very early version.
v1.2.61
Support Packet Capture in Diag Tools on EnGenius Cloud for cloud-managed ECS switch.
v1.2.60
Support Diag Tools on EnGenius Cloud for cloud-managed ECS switch.
v1.2.59
Apply new GUI design to device's web management pages.
Add DHCP IP auto-renew mechanism when cloud agent cannot check-in to server.
v1.1.58
Support optimized IGMP fast leave.
v1.1.57
Fine-tune ARP-validation mechanism to accommodate Mesh feature with ECW Cloud AP.
v1.1.55
Enhance PD Lifeguard feature with pending expiration.
Add "Version ID" for IGMP feature.
v1.1.52 (obsolete and will be updated soon)
Change Syslog write to flash level from INFO to Critical.
Support VLAN 0 to facilitate forwarding behavior.
Disable SSDP and mDNS features temporarily to avoid memory sizing issues.
For Multi-G series switches, PHY settings are adjusted to keep better ability of Interconnection to support most link-partners.
v1.1.49
Adjust header parsing rule for time-zone parameter. (cloud agent)
Adjust the SSDP and mDNS default configuration to disable. (It won't handle SSDP and mDNS packets by default setting.)
v1.1.47
Switch PoE scheduling feature will let user configure schedule via Cloud GUI when the device is powered by PoE of the port.
Switch LED on/off feature allows switch LED to be turned off at the upper-right corner in switch device detail page via Cloud GUI. (please be advised PoE Mode/LAN Mode LED cannot be turned off due to hardware limitation.)
Reset PoE from the port panel allows user to mouse-over PoE ports on switch port panel via Cloud GUI and power-cycle the port so the device attached to the port can be rebooted.
v1.1.42
Add GET/SET SNMP community for cloud agent.
Fix abnormal static route entry issue.
Fix abnormal default gateway issue.
Fix abnormal uplink port issue.
v1.1.40
Add Connection Diagnostic page in ECS local web management.
Add “Extend” link-speed mode in port setting page. (Not supported in multi-G series because it is without 10Mbps-speed.)
Support 2K static VLAN entries.
Adjust the hybrid service priority for Cloud Agent and WTP process.
Add "On", "Off" action for Scheduled PoE.
Add DHCP snooping / relay features for Cloud Agent.
v1.1.36
Update LED behavior code to cope with multi-G (5Gbps/2.5Gbps) LED color change from green to amber. 10Gbps LED remains green and 100Mbps/1Gbps remain amber as in previous v1.1.35.
v1.1.35
Bug Fixes
Fix DHCP client function that may cause system crash issue.
v1.1.31
Improvements
Resolve LBD behavior issue when STP enabled.
Add LLDP remote information ''system description'', ''remote capability support'', and ''remote capability enable''.
Renew the DNS server IP when receiving DHCP offer packet.
Bug Fixes
Resolve memory leak caused by abnormal DHCP packets.
v1.1.29
Improvements
Accommodate loop back detection mechanism for IOT devices.
Support trunk and mirror settings for cloud management.
Improve the efficiency to initiate cloud management service.
Add system warm start log to denote an expected software reboot.
Adjust default value of port rate limit to 1Mbps.
Web GUI now follows new 2020 California Password Law (SB-327) to force user changing password for a first time login.
Improve the way to show STP block/unblock status.
Support configure local credential in Cloud. Note that if the cloud already configured a different credential, the local credential will be synced to the cloud one automatically.
Bug Fixes
Fix the issue of packet buffer leak which may cause a system reboot.
Fix the issue that some specific DHCP packets sent by mikrotik router may cause system reboot.
Fix the bug that recurring setting of daylight saving does not work when SNTP service is not available.
v1.1.21
Improvements
Support cloud configuration on per port PVID and vlan members.
Bug Fixes
Correct the syslog timestamp issue.
Fix GUI and CLI issue by limiting the input format of User Account to Letters, Numbers, and underline character '_' only.
Fix GUI and CLI issue by excluding character '@' from password string.
v1.1.19
Improvements
Enhance DHCP settings to accommodate 2 sets of DNS server IP upon receiving multiple sets of DNS server IP from DHCP server.
Add system restart logs.
Bug Fixes
N/A
Last updated