LogoLogo
  • EWS Series User Manual
  • Product Overview
    • Introduction
    • LED Behavior
    • Comparison Table
    • Technical Specification
  • Getting Started
    • Management Interface
    • Connecting the Switch
  • Wireless Controller Features
    • Managing EnSky Access Points
    • Device Management
      • Access Points
      • Access Point Settings
      • AP Groups
      • Wireless Services
    • Monitor
      • Active Clients
      • Rogue AP Detection
      • System Log
      • Email Alert
    • Visualization
      • Topology View
      • Map View
      • Floor View
      • Mesh View
    • Statistics
      • Access Points
      • Wireless Clients
      • Real-Time Throughput
    • Hotspot Services
      • Captive Portal
      • Guest Account
    • Mesh
      • Mesh Profile
      • Node List
      • Mesh Tools
      • Isolated Nodes
    • Maintenance
      • Schedule Tasks
      • Troubleshooting
      • Bulk Upgrade
      • One-click Update
      • SSL Certificate
      • Check Codes
  • Ethernet Switch Features
    • System
      • Summary
      • Network Settings
      • System Time
      • Port Settings
      • PoE
      • EEE
    • L2 Features
      • Link Aggregtion
      • STP
      • MAC Address Table
      • LLDP
      • IGMP Snooping
      • MLD Snooping
      • Jumbo Frame
    • VLAN
      • 802.1Q
      • PVID
      • Voice VLAN
    • Management
      • System Information
      • User Management
      • Dual Image
      • SNMP
    • ACL
      • MAC ACL
      • MAC ACE
      • IPv4 ACL
      • IPv4 ACE
      • IPv6 ACL
      • IPv6 ACE
      • ACL Binding
    • QoS
      • Global Settings
      • CoS Mapping
      • DSCP Mapping
      • Port Settings
      • Bandwidth Control
      • Storm Control
    • Security
      • 802.1x
      • Radius Server
      • Access
      • Port Security
      • Port Isolation
      • DoS
    • Monitoring
      • Port Statistics
      • RMON
      • Log
    • Diagnostics
      • Cable Diagnostics
      • Ping Test
      • IPv6 Ping Test
      • Trace Route
    • Maintenance
      • Configuration Manager
      • Firmware Upgrade
  • Appendix
    • Appendix A
    • Appendix B
    • Appendix C
Powered by GitBook
On this page

Was this helpful?

Export as PDF
  1. Ethernet Switch Features
  2. QoS

Storm Control

PreviousBandwidth ControlNextSecurity

Last updated 4 years ago

Was this helpful?

Storm Control limits the amount of Broadcast, Unknown Multicast, and Unknown Unicast frames accepted and forwarded by the switch. Storm Control can be enabled per port by defining the packet type and the rate that the packets are transmitted at. The switch measures the incoming Broadcast, Unknown Multicast, and Unknown Unicast frames rates separately on each port, and discards the frames when the rate exceeds a user-defined rate.

Items

Descriptions

Port

Displays the ports for which the Storm Control information is displayed.

Status

Select whether Storm Control is Enabled or Disabled ingress on the interface.

Broadcast

Enter the broadcast rate in kilobits per second. The Gigabit Ethernet ports have a maximum speed of 1000000 kilobits per second. If the rate of broadcast traffic ingress on the interface increases beyond the configured threshold, the traffic is dropped.

Items

Descriptions

Unknown Multicast

Enter the Unknown Multicast rate in kilobits per second. The gigabit Ethernet ports have a maximum speed of 1000000 kilobits per second. If the rate of broadcast traffic ingress on the interface increases beyond the configured threshold, the traffic is dropped.

Unknown Unicast

Enter the Unknown Unicast rate in kilobits per second. The gigabit Ethernet ports have a maximum speed of 1000000 kilobits per second. If the rate of broadcast traffic ingress on the interface increases beyond the configured threshold, the traffic is dropped.

Click Apply to update the system settings.