LogoLogo
  • EWS Series User Manual
  • Product Overview
    • Introduction
    • LED Behavior
    • Comparison Table
    • Technical Specification
  • Getting Started
    • Management Interface
    • Connecting the Switch
  • Wireless Controller Features
    • Managing EnSky Access Points
    • Device Management
      • Access Points
      • Access Point Settings
      • AP Groups
      • Wireless Services
    • Monitor
      • Active Clients
      • Rogue AP Detection
      • System Log
      • Email Alert
    • Visualization
      • Topology View
      • Map View
      • Floor View
      • Mesh View
    • Statistics
      • Access Points
      • Wireless Clients
      • Real-Time Throughput
    • Hotspot Services
      • Captive Portal
      • Guest Account
    • Mesh
      • Mesh Profile
      • Node List
      • Mesh Tools
      • Isolated Nodes
    • Maintenance
      • Schedule Tasks
      • Troubleshooting
      • Bulk Upgrade
      • One-click Update
      • SSL Certificate
      • Check Codes
  • Ethernet Switch Features
    • System
      • Summary
      • Network Settings
      • System Time
      • Port Settings
      • PoE
      • EEE
    • L2 Features
      • Link Aggregtion
      • STP
      • MAC Address Table
      • LLDP
      • IGMP Snooping
      • MLD Snooping
      • Jumbo Frame
    • VLAN
      • 802.1Q
      • PVID
      • Voice VLAN
    • Management
      • System Information
      • User Management
      • Dual Image
      • SNMP
    • ACL
      • MAC ACL
      • MAC ACE
      • IPv4 ACL
      • IPv4 ACE
      • IPv6 ACL
      • IPv6 ACE
      • ACL Binding
    • QoS
      • Global Settings
      • CoS Mapping
      • DSCP Mapping
      • Port Settings
      • Bandwidth Control
      • Storm Control
    • Security
      • 802.1x
      • Radius Server
      • Access
      • Port Security
      • Port Isolation
      • DoS
    • Monitoring
      • Port Statistics
      • RMON
      • Log
    • Diagnostics
      • Cable Diagnostics
      • Ping Test
      • IPv6 Ping Test
      • Trace Route
    • Maintenance
      • Configuration Manager
      • Firmware Upgrade
  • Appendix
    • Appendix A
    • Appendix B
    • Appendix C
Powered by GitBook
On this page

Was this helpful?

Export as PDF
  1. Ethernet Switch Features
  2. VLAN

PVID

Previous802.1QNextVoice VLAN

Last updated 4 years ago

Was this helpful?

When an untagged packet enters a switch port, the PVID (Port VLAN ID) will be attached to the untagged packet and forward frames to a VLAN specified VID part of the PVID. A packet received on a given port would be assigned that port's PVID and then be forwarded to the port that corresponded to the packet's destination address. If the PVID of the port that received the packet is different from the PVID of the port that is to transmit the packet, the switch will drop the packet. Within the switch, different PVIDs mean different VLANs, so VLAN identification based upon the PVIDs cannot create VLANs that extend outside a given switch. If no VLANs are defined on the switch, all ports are then assigned to a default VLAN with a PVID equal to 1.

Port

Displays the VLAN ID to which the PVID tag is assigned. Configure the PVID to assign untagged or tagged frames received on the selected port.

PVID

Enter the PVID value. The range is from 1 to 4094.

Accept Type

Select Tagged Only and Untagged Only from the list.

Tagged Only: The port discards any untagged frames it receives. The port only accepts tagged frames.

Untagged Only: Only untagged frames received on the port are accepted.

All: The port accepts both tagged and untagged frames.

Ingress Filtering

Specify how you wish the port to handle tagged frames. Select Enabled or Disabled from the list.

Enabled: Tagged frames are discarded if VID does not match the PVID of the port.

Disabled: All frames are forwarded in accordance with the IEEE 802.1Q VLAN.

NOTE

To enable PVID functionality, the following requirements must be met:

  • All ports must have a defined PVID.

  • If no other value is specified, the default VLAN PVID is used.

  • If you wish to change the port's default PVID, you must first create a VLAN that includes the port as a member.

Click Apply to update the system settings.