LogoLogo
  • EWS Series User Manual
  • Product Overview
    • Introduction
    • LED Behavior
    • Comparison Table
    • Technical Specification
  • Getting Started
    • Management Interface
    • Connecting the Switch
  • Wireless Controller Features
    • Managing EnSky Access Points
    • Device Management
      • Access Points
      • Access Point Settings
      • AP Groups
      • Wireless Services
    • Monitor
      • Active Clients
      • Rogue AP Detection
      • System Log
      • Email Alert
    • Visualization
      • Topology View
      • Map View
      • Floor View
      • Mesh View
    • Statistics
      • Access Points
      • Wireless Clients
      • Real-Time Throughput
    • Hotspot Services
      • Captive Portal
      • Guest Account
    • Mesh
      • Mesh Profile
      • Node List
      • Mesh Tools
      • Isolated Nodes
    • Maintenance
      • Schedule Tasks
      • Troubleshooting
      • Bulk Upgrade
      • One-click Update
      • SSL Certificate
      • Check Codes
  • Ethernet Switch Features
    • System
      • Summary
      • Network Settings
      • System Time
      • Port Settings
      • PoE
      • EEE
    • L2 Features
      • Link Aggregtion
      • STP
      • MAC Address Table
      • LLDP
      • IGMP Snooping
      • MLD Snooping
      • Jumbo Frame
    • VLAN
      • 802.1Q
      • PVID
      • Voice VLAN
    • Management
      • System Information
      • User Management
      • Dual Image
      • SNMP
    • ACL
      • MAC ACL
      • MAC ACE
      • IPv4 ACL
      • IPv4 ACE
      • IPv6 ACL
      • IPv6 ACE
      • ACL Binding
    • QoS
      • Global Settings
      • CoS Mapping
      • DSCP Mapping
      • Port Settings
      • Bandwidth Control
      • Storm Control
    • Security
      • 802.1x
      • Radius Server
      • Access
      • Port Security
      • Port Isolation
      • DoS
    • Monitoring
      • Port Statistics
      • RMON
      • Log
    • Diagnostics
      • Cable Diagnostics
      • Ping Test
      • IPv6 Ping Test
      • Trace Route
    • Maintenance
      • Configuration Manager
      • Firmware Upgrade
  • Appendix
    • Appendix A
    • Appendix B
    • Appendix C
Powered by GitBook
On this page

Was this helpful?

Export as PDF
  1. Ethernet Switch Features
  2. ACL

IPv6 ACE

PreviousIPv6 ACLNextACL Binding

Last updated 4 years ago

Was this helpful?

Allows IPv6 Based Access Control Entry (ACE) to be defined within a configured ACL.

Items

Descriptions

ACL Name

Select the ACL from the list.

Sequence

Enter the sequence number which signifies the order of the specified ACL relative to other ACLs assigned to the selected interface. The valid range is from 1 to 2147483647, 1 being processed first.

Action

Select what action to take if a packet matches the criteria.

Permit: Forward packets that meet the ACL criteria.

Deny: Drops packets that meet the ACL criteria.

Protocol

Select the Any, Protocol ID, or Select from List from drop-down menu.

Protocol ID: Enter the protocol in the ACE to which the packet is matched.

Select from List: Select the protocol from the list in the provided field.

Source IP Address Value

Enter the source IP address.

Source IP Prefix Length

Enter the prefix length of the new source IP address. The range is from 0 to 128.

Destination IP Address Value

Enter the destination IP address.

Destination IP Prefix Length

Enter the prefix length of the new source IP address. The range is from 0 to 128.

Source Port

Select Single or Range from the list. Enter the source port that is matched to packets. The range is from 0 to 65535.

Destination Port

Select Single or Range from the list. Enter the destination port that is matched to packets. The range is from 0 to 65535.

TCP Flags

Select whether to handle each six TCP control flags; URG (Urgent), ACK (Acknowledgment), PSH (Push), RST (Reset), SYN (Synchronize), and FIN (Fin) from drop-down menu.

Don't Care: The ACE does not treat the TCP control flag.

Set: The packet with the TCP control flag being set matches the criteria.

Unset: The packet with the TCP control flag being unset matches the criteria.

Type of Service

Select Any or DSCP to match from drop-down list. When DSCP to match is selected, enter the DSCP. The range is from 0 to 63.

Click Apply to update the system settings.