EWS850-FIT
EnGenius Fit 802.11ax 2x2 Dual-Band Managed Outdoor Wireless Access Point (EWS850-FIT)
Introduction
This Quick Start Guide is designed to guide you through the installation of the Fit6 2x2 Outdoor access point, model EWS850-FIT, including hardware mounting and configuration.
Fit6 2x2 Outdoor
EnGenius Fit 802.11ax 2x2 Dual-Band Managed Outdoor Wireless Access Point
Model: EWS850-FIT
Wi-Fi 6 technology for high-performance Wi-Fi in high-density, multi-device environments.
Two spatial streams support up to 1,200 Mbps (5GHz) & 574 Mbps (2.4GHz).
Multiple applications for cloud and on premises solutions
Package Contents
System Requirements
Web Browser
Google Chrome (57.0.2987.110 and later)
Microsoft Edge (80.0.361.103 and later)
Mozilla Firefox (52.0 and later)
Hardware Overview
Ports
Reset by EnGenius PoE Adapter :
Reset to default: Press and hold the reset button on the PoE adaptor for over 10 seconds, and the LED (PWR) will start Fast Flashing (0.2 sec). Then, the device will be reset to factory default settings.
LEDs
Hardware Mounting
The access point can be mounted on the Wall and Pole, and please perform the steps for the appropriate installation:
Wall Mount
Determine where the Access Point is to be placed and mark the location on the surface for the four mounting holes. Use the appropriate drill bit to drill four 8.1mm diagram and 26mm-deep holes in the markings.
Screw the Anchors into the holes until they are flush with the wall.
3. Fasten the Mounting Bracket with the included Screws into the Anchors.
4. Hang the Access Point against the wall on the Mounting Bracket.
5. Secure the Access Point on the Mounting Bracket with the secure lock on the side.
Pole Mount
Thread the open end of the Pole Mounting Strap through the two tabs on the Mounting Bracket.
2. Lock and tighten the Pole Mounting Strap to secure the Mounting Bracket onto the pole.
3. Hang the Access Point onto the Mounting Bracket.
4. Secure the Access Point on the Mounting Bracket with the secure lock on the side.
Powering the EnGenius Fit AP
EnGenius Fit AP devices can be powered by any of the following:
EnGenius Fit PoE switches or 802.3af/ 802.3at PoE+ compliant switches
EnGenius PoE adapter (EPA5006GR)
Caution: Do not use both power sources at the same time.
Connecting to a PoE Switch
Connect the Ethernet cable from the EnGenius Fit AP directly to the PoE port of the PoE switch.
Powering with a PoE Adapter
(A) Connect one end of the Ethernet cable into the LAN (PoE) port of EnGenius FIT AP and the other end to the PoE port on the PoE Adapter.
(B) Connect the power cord with the PoE Adapter and plug the other end into an electrical outlet.
(C) Connect the second Ethernet cable into the LAN port of the PoE Adapter and the other end to the Ethernet port on the computer.
Management Plane
EnGenius Fit provides flexible options to manage your devices based on your network planning and deployment.
Option A: Cloud Management
Option B: On-Premises Management
Option C: Standalone Configuration
Cloud Management
Manage and monitor the Access Point through the FitXpress Platform with a mobile app or through the web portal.
FitXpress App (iOS/ Android)
⬇️ Download the FitXpress mobile app here
On-Premises Management
If you want to manage the device in on-premises mode, you need an onsite management station running the FitController connected to the same Layer 2 network.
FitController
FitController is a custom-built appliance with optimized network management software installed to ease onsite deployment without manual server configurations.
Standalone Configuration
Using your computer, you can connect to the same network (subnet) as the Access Point and use the web browser to access the device's local web GUI page for configurations whenever the device is set to Standalone mode.
Option A: Cloud Management with FitXpress
Step 1: Connecting Ethernet
Connect the Ethernet cable from the EnGenius Fit AP directly to the DHCP-enabled network and make sure the AP can reach the Internet.
Step 2: Register Device
You can register the access point with the FitXpress app.
Open the FitXpress mobile app and create an account.
Login and go to the Devices section. Click the Add(+) button.
Scan the QR code on the back of the device via the app.
4. If the camera successfully scans the QR code, the app will display the device information. You can tap "Register" to complete the registration.
Step 3: Connect to FitXpress
Once the device is powered on and ready to connect to the Internet, the PWR LED will stay Solid On, which means the device is now connected to the FitXpress platform. It will automatically download the default configuration settings from FitXpress for automated provisioning.
When the Access Point is connected to the FitXpress Platform for the first time, it will automatically check the latest firmware version available. If a firmware upgrade is required, it might take 8~10 minutes to complete the process. All LED indicators will be Flashing (0.5 sec) till the process is finished.
Step 4: Manage with the FitXpress
Log in to the FitXpress app to configure detailed settings and monitor your devices.
Option B: On-premises Management with FitController
Step 1: Connecting Ethernet
Connect the Ethernet cable from the EnGenius Fit AP directly to the DHCP-enabled network, which is the same Layer-2 network as FitController.
Step 2: Log in to the FitController
Launch your web browser to access the login page of FitController and create an account. Enter the email address and password that you created and click Sign In.
Step 3: Register Device and Assign to Network
Go to the System > Inventory page and click "Register Device (+)".
FitController will list all EnGenius Fit devices discovered from the same L2 network in the Pending Approval section. Select the device and Click "Register" to add to inventory.
From the Inventory page, Select the newly added device and click "Assign to Network" to add the device to your personalized network.
Step 4: Pairing the Device
Go to access point Device List.
Select the newly added device and click "Pairing" to allow the access point to build an encrypted connection between the device and FitController.
Step 5: Manage with FitController
Navigate to the left side menu to configure & manage your network and view network statistics using the FitController management interface.
Option C: Standalone Configuration
Step 1: Access to Local Web
Use your client device (e.g., a laptop, mobile device, or tablet) to find the SSID: "EnMGMTxxxx" and connect to it.
2. Under your web browser, enter the URL: http://EnGenius.local or http://192.168.1.1 to access the device's user interface.
3. Use the default login credential (ID/PWD: admin/admin) to log in to the device's local web page.
Step2: Configure and Manage the Device
After logging into the device's local web page, navigate to the left side menu to configure and manage the AP accordingly.
How to Change Management Mode?
EnGenius Fit devices support versatile network management methods, but the device can only be managed under one management mode at a time - either FitXpress, FitController, or Standalone. Therefore, you need to reset the device before changing to a different management mode. Then follow QSG instructions for the device onboarding.
Last updated
Was this helpful?