ENH500-AX
EnGenius Station Wi-Fi 6 2x2 5GHz Outdoor Long Range CPE (ENH500-AX)
Introduction
This Quick Start Guide is designed to guide you through the installation of the 2x2 Outdoor access point/CPE, model ENH500-AX, including hardware mounting and configuration.
Station6 2x2 Patch
EnGenius Station Wi-Fi 6 2x2 5GHz Outdoor Long Range CPE
Model: ENH500-AX
Wi-Fi 6 technology for high-performance Wi-Fi in high-density, multi-device environments.
Boost speed up to 1,200 Mbps air performance in 5GHz frequency band.
In conjunction with 2.4GHz management interface helps device configuration and monitoring more easily on a smartphone or tablet.
Package Contents
System Requirements
Web Browser
Google Chrome (57.0.2987.110 and later)
Microsoft Edge (80.0.361.103 and later)
Mozilla Firefox (52.0 and later)
Hardware Overview
Ports
Reset by EnGenius PoE Adapter :
Reset to default: Press and hold the reset button for over 10 seconds, and the LED (PWR) will start Fast Flashing (0.2 sec). Then, the device will be reset to factory default settings.
LEDs
Hardware Mounting
The access point can be mounted on the Wall and Pole, and please perform the steps for the appropriate installation:
Wall Mount
Determine where the Access Point is to be placed and mark the location on the surface for the four mounting holes. Use the appropriate drill bit to drill four 8.1mm diagrams and 26mm-deep holes in the markings of the Screw Position Identifier.
Screw the Anchors onto the holes until they are flush with the wall, and then fasten the Mounting Screws into the Anchors.
Hang the Access Point against the wall on the Mounting Screw Heads.
Pole Mount
Thread the open end of the Pole Mounting Strap through the two tabs on the Mounting Bracket of the Access Point.
2. Lock and tighten the Pole Mounting Strap to secure the Mounting Bracket onto the pole.
Powering the EnGenius Station AP
EnGenius Station AP devices can be powered the following:
EnGenius PoE adapter (EPA5006GR)
Powering with a PoE Adapter
(A) Connect one end of the Ethernet cable into the LAN (PoE) port of EnGenius Station AP and the other end to the PoE port on the PoE Adapter.
(B) Connect the power cord with the PoE Adapter and plug the other end into an electrical outlet.
(C) Connect the second Ethernet cable into the LAN port of the PoE Adapter and the other end to the Ethernet port on the computer.
Management Plane
EnGenius Station provides flexible options to manage your devices based on your network planning and deployment.
Option A: App Management
Option B: Standalone Configuration
App Management
Manage and monitor the Access Point through the EnWiFi Platform with a mobile app.
EnWifi App (iOS/ Android)
⬇️ Download the EnWiFi mobile app here
Standalone Configuration
Using your computer, you can connect to the same network (subnet) as the Access Point and use the web browser to access the device's local web GUI page for configurations whenever the device is set to Standalone mode.
Option A: App Management with EnWiFi
Station solution is a complete turn-key solution for managed Wi-Fi, not only with devices added to the management system but even during the deployment on the go. With the EnWiFi App, it facilitates the initial quick set-up for an AP or a group of APs before being added to the management system. This is especially helpful for service providers or operators to do initial deployment on-site with devices just taken out of the box with factory default settings.
For a configuration with a single device, upon AP power-up, this unmanaged AP will broadcast a specific management SSID for connection. Users can look at the back of the AP to match the last 6 digits of the MAC address with its corresponding SSID. For ease of group configuration on a bunch of APs sharing common settings, EnWiFi App is also capable of using a selected AP to discover all other APs for further configuration.
For WLAN deployments needing coverage extensions, besides devices’ wireless settings, EnWiFi App will also assist users in setting up WDS links to extend the coverage. After the App installation, follow the wizard for network setup.
Option B: Standalone Configuration
Step 1: Access to Local Web
Use your client device (e.g., a laptop, mobile device, or tablet) to find the SSID: "EnMGMTxxxx" and connect to it.
2. Under your web browser, enter the URL: http://EnGenius.local or http://192.168.1.1 to access the device's user interface.
3. Use the default login credential (ID/PWD: admin/admin) to log in to the device's local web page.
Step2: Configure and Manage the Device
After logging into the device's local web page, navigate to the left side menu to configure and manage the AP accordingly.
Last updated
Was this helpful?