Support Layer 7 Policy Based Route, allows administrator to designate which WAN port to be used for different applications.
Support Layer 7 firewall rule to block specific application that may hurt you network.
Support rollback configuration to prevent configuration errror that impact cloud connections.
Increase Layer 3 and Layer 7 firewall event logs, improving traffic visibility and easier for administrator troubleshoot their network.
Direct SecuPoint VPN user traffic using the gateway's PBR settings to ensure that all user traffic follows the same rules
Enhanced WAN disconnected log making WAN troubleshoot easier.
Support to disable LLDP for specific environment that do not allow auto discovery protocols. (Cloud does not support yet)
Support mDNS function making ESG easier to be found in local network. (Cloud does not support yet)
Fixed the issue where LAN subnets matching PBR rules could not route to other local subnets.
Fixed the issue that SecuPoint remote client can't access ESG’s local LAN if Passthrough mode and Split tunnel are enabled.
Enhanced firewall logs to output as a text file in real-time. (Cloud does not support yet)
Auto VPN Hub-and-Spoke supports full tunnel mode. (Cloud does not support yet)
Added support for static routing over VPN. (Cloud does not support yet)
When a rogue DHCP server is detected, an event log notification will be generated.
Added support to export NAT logs to an external syslog server. (Cloud does not support yet)
New dashboard displays WWAN information when WWAN is the primary WAN.
Added a new event log for reaching the maximum number of SecuPoint client seats.
Added a new event log for when the public IP and WAN IP are configured the same in NAT.
Support enable/disable HTTPs-only for local web page access. Allowing users force web UI access encrypted for better security.
Support enable/disable Local Web Page. Allowing users forbid local managements to prevent the confliction with the central cloud management.
Resolved an issue where the DDNS hostname was not displayed in the SecuPoint VPN client when passthrough mode was enabled.
Fixed an issue where the SecuPoint VPN client was non-functional when the primary WAN2 connection type was set to DHCP or a static IP address.
Addressed an issue where an Android phone (SecuPoint VPN client) could not access the internal server when SecuPoint VPN and port forwarding were enabled.
Corrected an issue where the latency monitor was inaccurate when the PBR function was enabled.
Fixed a problem with the Diag tool to prevent response failures.
Resolved an issue where the S2S VPN connection failed when the ESG uplink gateway changed its WAN IP address.
Fixed an issue where the VPN connection failed when the primary WAN was WAN2.
Fixed the issue for Auto Site-to-Site VPN connection sometimes getting disconnected upon WAN function reloaded with the following conditions:
Case 1: WAN IP is being changed (e.g., PPPoE IP changed)
Case 2: Fail-over under dual WAN
Case 3: IP getting changed in front end of Gateway
Fixed the issue for Diag Tool sometimes showing "This device is unavailable".
Fixed the issue for Site to Site VPN and IPsec Client VPN function that do not work properly with BASIC license.
Support Policy Route.
Support Gateway Access Control: VIP List and Block List.
Support Firewall Traffic Log - syslog server.
Support Packet Capture for WAN interfaces.
Adjust the definition and behavior of "System Name" and "Device Name"
Remove System Name setting from LSP.
Revise DHCP client hostname to {ModelName}-{MAC_last_4_digits}.
System Name support multi-language.
Automatically add a GRE port forwarding rule while adding PPTP TCP port: 1723
Revise Subnet Mask format of Static IP in LSP.
Optimize reset button behavior.
Fixed Gateway status issue when it shows online, it doesn't show WAN1/WAN2 IP information in Cloud UI.
Fixed the issue for Auto VPN where it failed if the number of ESG devices is more than 11.
Fixed the issue where the system becomes stuck upon continuously adding two bridge interfaces without assigning any Ethernet ports.
Use System Name as Host name for WAN via DHCP.
Enhance WAN security to close port 53 if Outbound FQDN rules are set.
Fixed the issue for Site-to-Site VPN connection not established after system reloading in some cases.
Fixed the issue for SecuPoint server to let it work in Passthrough Mode or under NAT.
Fixed the issue for ESG620 not able to connect to EnGenius Cloud via WAN2 connection when an unsupported SFP+ module is plugged into WAN1 port.
Support URL filtering and Block page. (Cloud page to be updated)
Support EnGenius and 3rd-party DDNS function in Passthrough Mode. (Cloud page to be updated)
Support Client traffic statistics. (Cloud page to be updated)
This f/w version is for the first release.