Hardware Mounting

The access point can be mounted on the Wall and Pole, and please perform the steps for the appropriate installation:

Wall Mount

A) Plug the dynamic stick into the bracket.

B) Screw the sealing nut and assembled parts, as well as tighten it.

C) Put the nock washer on the dynamic stick.

D) Assemble the mounting parts to the device.

E) Determine the mounting location. Mark and drill two pilot holes aligning to the screw holes of the bracket.

F) Put wall anchors into the holes and insert screw into the wall anchor.

G) Screw and secure the bracket in place.

Pole Mount

A) Plug the dynamic stick into the bracket.

B) Screw the sealing nut and assembled parts, as well as tighten it.

C) Put the nock washer on the dynamic stick.

D) Assemble the mounting parts to the device.

E) Thread the open end of the pole strap through the two tabs on the bracket.

F) Lock and tighten pole strap to secure bracket to the pole.

Introduction

This Quick Start Guide is designed to guide you through the installation of the 2x2 Outdoor access point/CPE, model EnStation6, including hardware mounting and configuration.

Package Contents

System Requirements

Web Browser

• Google Chrome (57.0.2987.110 and later)

• Microsoft Edge (80.0.361.103 and later)

• Mozilla Firefox (52.0 and later)

Hardware Overview

LEDs

Powering the EnGenius Station AP

EnGenius Station AP devices can be powered the following:

• EnGenius PoE adapter (EPA5006GR)

Hereby, EnGenius Networks declare that this product is in compliance with:

• Directive 2014/53/EU

• Regulations 2017 (S.I. 2017/1206)/ Regulations 2016 (S.I. 2016/1091)/ Regulations 2016 (S.I. 2016/1101)

• RoHS 2015/863

• WEEE 2022

• REACH Regulation

• Maximum data rates are based on the IEEE standards. Actual throughput and range may vary depending on many factors including environmental conditions, the distance between devices, radio interference in the operating environment, and the mix of devices in the network.

• Features and specifications are subject to change without notice.

• This device complies with Part 15 of the FCC Rules.

• Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

• Trademarks and registered trademarks are the property of their respective owners. For the United States of America: Copyright © 2023 EnGenius Technologies, Inc. All rights reserved.

Management Plane

EnGenius Station provides flexible options to manage your devices based on your network planning and deployment.

Option A: App Management

Option B: Standalone Configuration

Option B: Standalone Configuration

Step 1: Access to Local Web

1. Use your client device (e.g., a laptop, mobile device, or tablet) to find the SSID: "EnMGMTxxxx" and connect to it.

2. Under your web browser, enter the URL: or http://192.168.1.1 to access the device's user interface.

3. Use the default login credential (ID/PWD: admin/admin) to log in to the device's local web page.

Step2: Configure and Manage the Device

After logging into the device's local web page, navigate to the left side menu to configure and manage the AP accordingly.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

(If device is outdoor AP, please delete it. If device is indoor AP, need to add it.)

This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.

For mobile device usage (>20cm/low power)

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

CE

The device complies with Directive 2014/53/EU issued by the Commission of the European Community.

Standards:

• ETSI EN 300 328 V2.2.2 (2019-07)

• ETSI EN 301 893 V2.1.1 (2017-05) Final Draft

• ETSI EN 303 687 V0.0.20 (2022-03)

• EN 55032:2015+A1:2020 EN 55035:2017/A11:2020 ETSI

UKCA

The device is in conformity with the relevant legislation of United Kingdom: 2017 (S.I. 2017/1206)/ Regulations 2016 (S.I. 2016/1091)/ Regulations 2016 (S.I. 2016/1101).

Standards:

• EN 300 328 V2.2.2 (2019-07)

• EN 301 893 V2.1.1 (2017-05) Final Draft

• EN 303 687 V0.0.20 (2022-03)

• EN 55032:2015+A1:2020

IC

This device complies with ISED’s license-exempt RSS. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

Option A: App Management with EnWiFi

Station solution is a complete turn-key solution for managed Wi-Fi, not only with devices added to the management system but even during the deployment on the go. With the EnWiFi App, it facilitates the initial quick set-up for an AP or a group of APs before being added to the management system. This is especially helpful for service providers or operators to do initial deployment on-site with devices just taken out of the box with factory default settings.

For a configuration with a single device, upon AP power-up, this unmanaged AP will broadcast a specific management SSID for connection. Users can look at the back of the AP to match the last 6 digits of the MAC address with its corresponding SSID. For ease of group configuration on a bunch of APs sharing common settings, EnWiFi App is also capable of using a selected AP to discover all other APs for further configuration.

For WLAN deployments needing coverage extensions, besides devices’ wireless settings, EnWiFi App will also assist users in setting up WDS links to extend the coverage. After the App installation, follow the wizard for network setup.