Hereby, EnGenius Networks declare that this product is in compliance with:

• CB IEC-62368

• RoHS 2015/863

• REACH Regulation

• Maximum data rates are based on the IEEE standards. Actual throughput and range may vary depending on many factors including environmental conditions, the distance between devices, radio interference in the operating environment, and the mix of devices in the network.

• Features and specifications are subject to change without notice.

• This device complies with Part 15 of the FCC Rules.

• Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

• Trademarks and registered trademarks are the property of their respective owners. For the United States of America: Copyright © 2023 EnGenius Technologies, Inc. All rights reserved.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditins: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CE

The device complies with Directive 2014/30/EU issued by the Commission of the European Community.

Standards:

• EN 55032:2015+A11:2020

• EN 55035:2017+A11:2020

UKCA

Standards:

• EN 55032:2015+A11:2020

• EN 55035:2017+A11:2020

ISED

The device is in conformity with the relevant legislation of Innovation, Science, and Economic Development Canada (ISED): 2020

Standards:

• ICES-003:2020 Issue 7

Introduction

This Quick Start Guide is designed to guide you through the installation of the FitController100, model FitCon100, including hardware mounting and configuration.

Package Contents

System Requirements

Web Browser

• Google Chrome (105.0.5195.127 or later)

Network Requirements

Before you get started, please make sure your network environment is DHCP-enabled. EnGenius FitController is assigned with a default IP address dynamically by the DHCP server.

Please also make sure all the devices managed by the controller are in the same L2-network as the controller.

Hardware Overview

Ports

LEDs

Hardware Mounting

1. Mark the screw position with the Screw Position Identifier.

2. Drill the holes with 7mm diameter and 24mm depth on the marks.

3. Insert the Anchors into the drilling holes until they are flush with the wall.

4. Insert and tighten the Screws into the Anchors, but leave the screw head sticking out so you can hang the Controller on it.

5. Hang the Controller against the wall onto the Screw heads.

Power On Device

The EnGenius FitCon100 devices can be powered by any of the following:

• EnGenius Cloud PoE Switch or 802.3af PoE+ compliant Switch

• Power Adapter (DC 12V power input)

Connecting to a PoE Switch

Connect the Ethernet cable from the EnGenius Fit Controller directly to the PoE port of the PoE switch.

Powering with a Power Adapter

Connect the Power Cord to the adapter, and then plug the Power Cord into the power outlet.

Configuration

Step 1: Access to the Web Page

You can access the controller's web page by using the controller's DHCP-assigned IP or default IP address.

Connect to Controller via DHCP-assigned IP

1. Connect the controller to the network and ensure that your host system is on the same Layer-2 network as the controller.

2. Check the DHCP server for the controller's IP address, and enter the IP on your browser's address bar to access the device's user interface.

Connect to Controller via Default IP

1. Connect the controller to your computer and ensure its IP address is in the same subnet.

2. Under your web browser, enter the URL: http://192.168.1.250:8080 to access the device's user interface.

Step 2: Create Account and Log In

Create your own account and password to log in to the controller's local web page.

Step 3: Configure and Manage the Device

After logging in to the device's local web page, navigate to the left-side menu to configure and manage the controller accordingly.